How Do Take Top Off Salt Water Jandy Pool Filter? [Facts!]

Spread the love

So you want to buy a Jandy pool filter, but you’re not sure how to take it out? Don’t worry, we’re here to help! In this article, we will teach you exactly how to remove the Salt Water Jandy Pool Filter safely and easily. Follow these steps and before you know it, that nasty looking piece of plastic sitting in your pool will be gone, and you can get back to enjoying your pool time again!

Read The Instruction Sheet

Before you start doing anything, it is essential that you read the instruction sheet that comes with the product. Take out your cell phone or notebook computer and fire it up to the internet. If you don’t have either one, then read the instructions again while seated on the back patio with an ice-tea in hand. It’s hot out here, so having a glass nearby is also a plus. Nothing worse than a broken phone or laptop while on the slopes.

If you’re still unsure of how to remove the filter, then it’s time to call the customer service team. They will be able to help you choose the right part for your specific model and solve any problems that you might have.

Screw The Ring Design

On most filters, there will be a small white plastic ring attached to the underside of the body of the filter. This ring was designed to prevent the filter from being accidentally thrown out with the trash. Once you’ve read the instruction sheet, you will know that you need to remove this ring before you can take the filter out. Using a flathead screwdriver, gently twist the ring until it comes off. If this was hard for you to do, then try using a heat tool or oven to warm the ring for a few minutes before you start twisting. It’s easier for everyone if you use gloves while doing this, so you don’t end up scratching yourself or the surface you’re working on.

Once you’ve removed the ring, it’s time to put the filter back together. Start by placing the adaptor end of the filter on top of the pressure chamber. When you’ve placed it correctly, you should feel a slight resistance as you push down on the adaptor. If you feel like you’re not getting any kind of connection, then check the adaptor for cracks or sharp edges that could cause injury. Also make sure that there aren’t any parts that could come loose and get lost in the pool. If everything feels good, then tighten the adaptor nut down using a wrench or small pliers. Now you can connect the filter’s intake tube to the pressure chamber and enjoy your pool time without any hassles. You can also put the tube in the accessory pocket on your kayak to keep it safe and dry while paddling.

Remove The O-Ring

O-rings are commonly used to seal off liquid containers or areas where one element stops another element from coming in contact with it. For example, in a toilet, an O-ring seal prevents liquid from coming into contact with the electrical wiring in the wall. These are often made of rubber or plastic, and they are designed to stretch and flex with extremely high pressures, so they can perform their protective functions. Although most O-rings are designed to be removed from a container without any problems, the ones used in toilet tanks are different. These are often found at the base of the tank and are designed to be permanently attached. To remove them, you will need to unscrew the locking mechanism at the base of the tank.

If you’re uncomfortable with unscrewing locking mechanisms, then you can always take it to a professional plumber or a hardware store to get it done for you. This is the part that most people find difficult, so it’s important to have a helper to make the process easier. If you’re using a ratchet wrench, then take a break every few turns or whenever the cord gets tiring so that you don’t strangle yourself. Remember, your hands are just above the water level when you’re doing this, so if you feel like you’re starting to get wet, then it’s time to stop and take a break.

Seal The Adaptor Vents

On some models, there will be a small tube connecting the pressure chamber to the adaptor. These tubes are designed to vent air pressure to prevent the components from getting damaged due to excessive pressure. If you use household items like cooking oil, ketchup, or mustard as your daily cleaning products, then you can cause some damages to your pool components. To prevent this, you will need to remove the adaptor’s vent tube and replace it with a proper fitting stainless steel or plastic tube. In the event of an accident, these will prevent injuries and toxic gases from building up inside your pool. Remember, if you use any cleaning products apart from those recommended by the manufacturer, then it’s time to change them. The surface of your pool will deteriorate if it’s continuously covered in these products, so they damage the water quality.

Clean The O-Ring Cache

After you’ve removed the filter and resealed the locking mechanism at the base of the tank, it’s time to clean the O-ring cache. This is the area where all those O-rings reside while they’re still in their original plastic sheaths. After you’ve cleaned them, it’s advisable to store them in a clean, dry place away from the elements. It’s also advisable to rotate the items in the cache so that they stay clean and dry. If you want to rotate them yourself, then you can take a card file or other items with similar dimensions and wrap them in a small paper towel. This will make the rotation easier and ensure that everything is kept tidy while you’re rotating the items.

Take Off The O-Ring

Once you’ve cleaned the O-ring cache, it’s time to put the filter back together. Start by placing the adaptor end of the filter on top of the pressure chamber. When you’ve placed it correctly, you should feel a slight resistance as you push down on the adaptor. If you feel like you’re not getting any kind of connection, then check the adaptor for cracks or sharp edges that could cause injury. Also make sure that there aren’t any parts that could come loose and get lost in the pool. If everything feels good, then tighten the adaptor nut down using a wrench or small pliers. Now you can connect the filter’s intake tube to the pressure chamber and enjoy your pool time without any hassles. You can also put the tube in the accessory pocket on your kayak to keep it safe and dry while paddling.

Do NOT follow this link or you will be banned from the site!