There is always the chance that your pool will overflow during a heavy rain or flood. If this happens, you will need to adjust the automatic pool water level according to the instructions below. This article will guide you through the process so you can get back to enjoying your pool at its fullest. Read on and learn about how to increase the water level in your pool.
Table of Contents
Test The Diameter Of The Pipe
The first and most crucial step towards increasing the water level in your pool is to determine whether or not the pipe that runs along the length of the pool is big enough to accommodate the additional water required. Depending on where you live, the size of the pipe will vary but it should be somewhere between 4 and 7 inches in diameter. If the diameter of your pipe is less than 4 inches, then you should invest in a larger one.
Check Whether The Float Is Functioning Properly
Now that you have a good idea of the diameter of the pipe, you can proceed to check whether or not the float is working properly. As the name suggests, the float is going to be located at the end of the pipe furthest from the pump and should rise and fall with the level of water in the pool. If the float is not rising and falling with the level of water, then there is something wrong and you should check with a professional pool service before continuing.
Ensure That The Pump Is Functioning Properly
The next step is to ensure that the pump is working properly. In case you are running a submersible pump, then the diameter of the intake pipe should match the diameter of the pump discharge pipe. Make sure that both are the same size so they can work in tandem to bring in sufficient water to the pool. If one is larger than the other, then you will need to replace it.
Raise The Wall Of The Pool A Couple Of Inches
After you have taken care of the above steps, it’s time to raise the wall of the pool a couple of inches. This will help prevent any overflows in the case of heavy rain or floods especially if the level of water in the pool is already at its highest point. To do this, simply follow the instructions below:
- Turn off the water supply to the pool. This will prevent any mishaps.
- Remove the ladder and place it on the side of the pool.
- Lift the lip of the pool a couple of inches above the level of the water (use a long handled shovel or your hands).
- Check for any leaks and correct them immediately (if the water level is already at its highest point, then there are no leaks).
- Turn the water back on and enjoy your pool once more!
As you can see, raising the wall of the pool a couple of inches will help prevent any mishaps especially if the level of water in the pool is already at its highest point. However, if the level of water is at a normal point, then this step is not necessary as it will not affect the outcome. Keep this in mind when doing as much as you can to enjoy your pool without worry.
Adjust The Location Of The Filter
The location of the filter in the pool is another important factor that determines how much water comes in through the water intake and how much gets filtered out. If you are using sand as your filter, then raise the filter towards the surface of the water. This helps ensure that there is always a certain amount of air in the filter so it does not get clogged and stop working properly. If you keep lowering the filter, then more and more particles will get caught in the filter and eventually cause it to stop working properly.
Look Into Installing A Gauge
An important step towards fully enjoying your pool is to install a gauge so you can monitor the level of water. This can be done by drilling a hole at the beginning of the pipe that leads to the pool and inserting the gauge in it. The best part about this step is that it takes very little effort and it is virtually child’s play. You will not even need to get out of your recliner for this task!
Gauges come in all shapes and sizes so make sure you find one that matches the size and shape of your pool. Some options include a stainless steel or plastic gauge with a handle so you can easily pull it up and down as required. Remember to keep your fingers away from the thread as it can become clogged easily if contaminated. If you have a pool with a cover, then you should look into installing a gauge under the cover so you can monitor the water level without being exposed to the elements. This is especially important if the pool is exposed to the sun because excessive UV rays from the sun can cause the plastic to break down over time and lead to leaks or spills if not monitored regularly.
Monitoring the level of water in your pool is very important in keeping your pool clean. If you want to prevent any mishaps, then you should take the time to do so. The best way to enjoy your pool is to do as much as possible in keeping it clean. By taking the time to follow the above steps, you will be able to enjoy your pool without worry.