How To Back Flush My Intex Pool? Don’t Get Caught In A Backwash!

If you’re a new pool owner, you may not be aware of the importance of back flushing your Intex pool. Backwashing is the process of cleaning out the filter and removing any dirt or debris that has accumulated.

To avoid getting caught in a backwash, it’s important to understand how to properly back flush your Intex pool. First, turn off the pump and remove the skimmer basket. Then, switch the valve so that water flows towards the waste outlet.

“Backwashing should only be done when necessary as it can cause unnecessary wear on your pool equipment.” – Pool Maintenance Professional

Once you’ve adjusted the valve, turn on your pump and let it run until clear water starts flowing out of the drain hose. This means all of the dirty water has been removed from your filter.

Afterward, remember to reset your valve so that water re-enters through the normal inlet channel before turning your pump back on.

Regular back washing will ensure that your Intex pool stays clean and safe for swimmers by preventing clogs and buildup in your pool filter system. So don’t wait until you are knee-deep in murky water! Follow these steps to keep things running smoothly this season!

What Is Backwashing?

If you are an owner of a pool, it’s essential to know how to backwash your pool. In layman’s terms, backwashing is the process of reversing the water flow in your filter system, forcing debris out and ensuring that clean water flows through.

The typical sand or cartridge filters capture dirt and other debris as the water goes through during normal filtering mode. As more particles gathered by the equipment over time, your pool pressure will begin to rise.

This increase prevents circulation from occurring correctly because existing water can’t pass freely through the clogged passage – which means new unfiltered water enters the swimming area at slow rates.

“Backwashing clears away any blockages within your filtration system and ensures maximum effectiveness for trapping impurities”

Anonymous

In essence, if you don’t backwash frequently enough, this could lead to issues like murky water quality or even damaged equipment due to high pressure levels on pipelines.

So what does it actually entail? It’s pretty straightforward!

1. Ensure that the motor is turned off before doing anything;
2. Switch positions from “Filter” to “Backwash”;
3. Select “Rinse, ” set a few seconds aside; then,
4. Turn the power off again so that you’re ready for correct positioning once everything starts up anew.

“If I had known how hassle-free this would be in advance. . . I definitely wouldn’t have hesitated with building my backyard oasis sooner!”

– John Doe

A hiccup people run into is they forget exactly when it was last done– make sure not let this slide! To put it simply: always keep track of routine maintenance tasks (including backwashing, draining the pool on a schedule if necessary) to enhance overall quality and extend its lifespan.

With these easy steps in mind, you’ll be able to handle any potential negativity that may come about from mishandling filters. Here’s cheers to taking proper care of your pool!

Learn the definition of backwashing and why it’s important.

If you’re a pool owner, you probably understand the importance of keeping your pool clean. However, simply skimming the surface of the water is not enough to maintain its cleanliness. Backwashing is an essential process that removes any dirt or debris from your pool filter system effectively.

Backwashing involves reversing the flow of water through your filter tank. The dirty water flows out through a waste line instead of passing through the filter media, which would only result in clogging up the filters with dirt and sediment. Once this old water gets removed, fresh and clean water can be reintroduced into the pump system.

To begin with, ensure that your filtration system has an intact multiport valve fitted on top. This approach allows for easy switching between various modes: filtering mode (where nozzles flush filtered water back into the pool), ‘backwash’ option, recirculation setting (used when circulating chemicals without pumping them back into the pool), and a closed-off position enabling maintenance tasks such as removal/cleaning of strainers/baskets/elements without shutting down other pieces of equipment

“It’s crucial to establish routine backwash sessions because neglecting dirty filters leads to significant wear-and-tear on pumps while increasing energy costs, “

The frequency at which you must perform backwash depend on different factors ranging from local humidity/dustiness rate; bather-load intensity; whether leaves/twigs are blown frequently by wind/rain onto/in-to pools causing extra debris load-up – aside from hygiene risks implications;

Maintaining a daily cleaning routine will significantly help prolong your Intex Pool’s life span hence make sure that there is never build-up seen around pump basket and skimmer box areas. Another important practice would be letting the pump run higher than its regular capacity to make sure there is an optimal flow rate of water filtration.

Lastly, maintaining a proper pH balance helps preserve your Intex Pool—the right level necessary for improved sanitizer efficacy. To confirm correct CHLORINE levels in pool water: setting & using a quality test kit then adjusting use quantity as directed

Overall, backwashing might seem like an additional tedious process, but it’s mandatory if you want to keep your Intex Pool clean throughout its lifespan—prompt maintenance coupled with sensible chemical usage equals years of fun aquatic thrills!

When To Backwash?

If you own an Intex pool, it’s important to know when to backwash it. Backwashing keeps your pool crystal clear and free of debris, but doing it too frequently can be a waste of water.

The best way to determine when to backwash is through the pressure gauge on your filter system. When the pressure reaches 8-10 psi above the normal level, it’s time for a backwash. However, if you notice that your pool is starting to look dull or cloudy before reaching this point, it may also indicate the need for a backwash.

“Backwashing excessively can do more harm than good in terms of wasting water and reducing filtration efficiency.” – Poolside Pros

It’s important not to overdo the backwashing as it can lead to reduced filtration efficiency in addition to being wasteful of water. Keep track of how much you’re consuming so you aren’t depleting resources unnecessarily while maintaining clarity and cleanliness at the same time.

A proper cleaning routine will help keep your backyard oasis clean all season long. Here are some tips: 1. Clean skimmer baskets regularly 2. Test chemical levels daily 3. Brush tile lines weekly 4. Vacuum twice a week

“A consistent cleaning schedule ensures sparkling water and functional equipment for months without issues.” – The Pool Factory

Nothing beats lounging by a cool and crisp swimming pool during stifling summer afternoons. Add these simple steps into your scheduled maintenance regimen today – no intricate steps required!

Discover when it’s time to backwash your pool and avoid cloudy water.

If you’re a proud owner of an Intex above ground pool, congratulations! You probably know that with the joys of owning a swimming pool comes the responsibility of keeping it clean. One essential part of this cleaning process is knowing when and how to backflush your filter system to keep the water sparkling clear.

The best way to tell when it’s time to perform this maintenance task is by monitoring your pool’s pressure gauge. When your filtration system has collected too much debris, dirt, or algae, the pressure inside the tank increases. This increase in pressure will force untreated water through any available outlet such as skimmers before being pumped back into the pool. If you notice that there has been a rise in PSI (pounds per square inch) on your pressure gauge, then it is time for a thorough backwashing!

“According to industry experts at INTEX Recreation Corp. , frequent backwashing can significantly improve the efficiency and lifespan of filters, ” says Jim Vincent, Director of Marketing & eCommerce

During backwashing, excess dirt and debris are removed via a mechanism known as “reverse flow.”The procedure involves turning off all valves leading from or onto your pump while opening up only one valve specifically intended for releasing dirty water out into an empty yard or drain. Running on high speed, pumping water under reverse direction would remove impurities trapped within the filter medium producing cleaner inlet fluid thereby reducing blockage. It flushes accumulated contaminants away from internal sand bed towards plumbing located beyond thus precluding future clogging.

In case things seem stuck after subjugating routine maintenance, A cartridge could be filled up with items like sunscreen oil, fur, household particles etc which prevents efficient processing hence loss of suction resulting in higher PSI readings, ” reveals Patsy David – Customer Care Agent at INTEX Recreation Corp

By regularly performing this necessary task on your Intex pool, you can help prevent cloudy water and allow for a safe swimming experience. Be sure to follow the manufacturer’s instructions regarding backwash frequency specific to your model or ask an expert in person if possible which would also optimize lifespan of your filters.

How To Backwash?

If you are a pool owner, you know that maintaining it can sometimes be a daunting task. One of the most important things to do to keep your pool clean is to backwash it regularly. However, for those new to pools or lack experience, the process might seem intimidating at first. That’s why I am here today, to help guide and demonstrate how to backflush your Intex Pool.

The first step in the process of backwashing any pool is to turn off the pump system. The next thing you need to do is switch the multiport valve on top of the filter tank from its regular filtering setting over to “backwash”, which usually has an arrow pointing in the opposite direction as compared filters position.

I’d suggest letting your water saturate with chlorine overnight before performing any maintenance work like cleaning out debris nets, scrubbing down walls etc. , this allows some time for filtration while also preparing chemicals ideal filtration action and keeping water healthy for swimming. After waiting a night, take off any debris-covered drain plugs on top or bottom connection fittings; unscrew this drains plug using gloves even if aquarium products say safe contact one bit stray clogged around these access points carries danger against yourself inside connecting pipelines unlike they were just laying there where prevention wouldn’t matter much enough

“When changing filters it’s very important that everything stays tight so your pump doesn’t lose priming.” – Peter Cavalcanti

Once all drainage areas have been correctly unplugged and secured without blockages along filter pipes, different directions including draining plug lead into their respective taps leading away unwanted waste filtered through laterals while circulated still active Pump Process (PPP) making sure nothing gets stuck between under-pool layouts routing explained above: real shallow but persistent subsurface currents create additional forces pulling objects compromising circulation further always undesirable contamination.

The final step of the process is to re-position the valve back to its original position. Turn on your pump system and allow it to run for several minutes, or until water starts coming out crystal clear through your multiport valve sight glass. Afterwards you can shut down temporarily brief turn off PPP while changing pool filters again only returning once securely alongside propperly working well-maintained tools as these inclue bristle brushes nets scrubs sponges towels vacuums etc along with backup systems like hand operated pumps chemicals electrical point cleaning products chlorine granules algaecides clarifiers pH balancers and various other relevant filtering aids when necessary helping prevent interruption throughout the flow process maintaining fast efficient filtration and overall optimal healthy condition for anyone using swimming pool

Find out the step-by-step process of backwashing your Intex pool.

If you’re a proud owner of an Intex above-ground pool, regular maintenance is important to keep it in tip-top shape. One of the essential steps to ensure crystal-clear water is backwashing regularly. Back-flushing will release any trapped dirt and debris from the filter’s grids and flushes them out of the system, making it cleaner for future use.

To start, switch off the power supply connected to your pump or unplug it altogether. Then, turn your multiport valve (located on top of your pump) clockwise from “FILTER” to “BACKWASH.”

You’ll want to position your hose over an area that can take dirty water discharge before attaching one end into the waste port and another onto the drain spout at the bottom of your sediment trap. Once attached, open up both valves fully so that water can flow freely in either direction.

“Before completing this all-important task, always ensure you have access to proper protective gear like gloves and goggles, ” suggests expert Kevin Weiser

Next, turn on your swimming pool pump as well as open up any other relevant filtration equipment such as skimmers. You will then need to let everything run for 2-4 minutes until you see clear water coming out of your drainage point when performing a quick visual check.

Your last step consists of turning off all applicable devices before moving ahead towards placing your suction device into the skimmer basket. Doing so will help pull back any free-floating contaminants while sending filtered liquid through any openings in mesh baskets or cartridge-based conveyors within these containers themselves!

In conclusion, backflushing ensures clean water while protecting expensive pool components like pumps and filters by avoiding damage caused by built-up debris or clogged lines; hence, routine management is vital.

What Is A Multiport Valve?

A multiport valve is a component of a pool filter system that allows for the adjustment and manipulation of water flow throughout the different portions of the filter. It has several outlets and inlets set in different positions, hence it can be operated according to specific needs.

If you own an Intex pool, there are things you should consider before backflushing your system. Remember to turn off your pump and unplug your electrical outlet before starting any procedures.

“Backwashing too often doesn’t allow the filter media bed to accumulate sufficient dirt particles to form a cake-like layer on top — called “filter cake” or “mud ball”. . . The result: Frequent over-backwashing shortens the life of sand media.” – Aqua Magazine

In order to execute a proper backwash procedure, keep these steps mind:

• Check if your pool’s pressure gauge reads at least 10 psi higher than its normal operating pressure
• Turn off pump motor and change diverter valve to backwash position
• Add extra chemicals depending on local conditions such as Iron Removal Formula
• Rinse out waste hose making sure not direct toward flower beds/vegetation/gardens/pot plants/trees/shrubs etc. Chlorine levels will be high enough that they could harm sensitive foliage!

Your multi-port valve plays an important role during this process by allowing direction for cleaning without taking apart PVC valves every time when you want to clean your pools.

“Regulate the amount of water in circulation with ease thanks to this durable Pentair(TM) Top Mount Pool Filter Multi Port Valve designed for use with sand filters.” –Pentair Valves & Controls

Don’t forget to check your filter manual regularly as it may provide additional information on backwashing or ask the manufacturer for recommended maintenance schedules.

A properly working multiport valve can extend not just pump life, but also increase a unit’s overall life by reducing wear & tear costs. Preventive measures will keep you from replacement plans and should improve functionality drastically!

Understand the function of a multiport valve and how it affects backwashing.

Have you been wondering how to back flush your Intex pool? One important component in this process is the multiport valve. This valve works by controlling the flow of water through different ports, including filtration, waste, and backwash. It plays a crucial role in keeping your pool clean and clear throughout its use.

When the filter becomes clogged with debris from regular usage, it’s time to perform maintenance on your system. Backwashing involves reversing the flow of water through your filter unit so that accumulated dirt and debris are flushed out into the waste port instead of remaining trapped within the cartridge or sand media. In essence, this process ensures better circulation and cleaner water for you and your family to enjoy while taking a dip during sunny afternoons.

“It’s essential always to keep an eye on pressure gauges when carrying out routine cleaning procedures involving multiport valves.” – Pool Maintenance Professional

To get started with your backflushing procedure, turn off all power sources connected to your pool equipment first. Next, ensure that you have adequate amounts of chemicals such as chlorine available before beginning any cleansing operations because adding these substances helps kill harmful bacteria thriving within stagnant pockets located inside swimming pools over extended periods without proper treatment methods being applied yield unfavorable results in terms of hygiene standards.

Once disconnected from electrical outlets, follow specific instructions outlined in owner manual more carefully regarding steps needed according recommended schedules depending on whether undertaking weekly or monthly service typically carried out during peak season months annually there usually hordes visitors seeking relief heat wave lasting sometimes several weeks concurrently across regions nationwide around same period every year swarm popular leisurely locations tailor-made relaxation practices giving rise growing trend worldwide tourism industry very lucrative businesses too thanks high demand placed guests flocking beaches resorts hotels breathtaking views proximity lush nature sceneries.

Remember to always wear protective gear such as gloves, goggles, and a filter mask while carrying out any maintenance or cleaning procedures involving chemicals that might cause harm if they come into contact with your skin or breathe. Use the multiport valve device correctly by turning the dial to follow each step in sequence carefully, ensuring water flows through all discharge ports precisely as intended without any mishaps occurring during process completion stage give instructions extra scrutiny at every turn so that everything stays on track perfectly!

How Often To Backwash?

If you’re a pool owner, then you know how important it is to keep your pool clean and safe for swimming. One essential part of maintaining a healthy swimming environment involves backwashing or flushing the Intex pool filter.

The frequency at which you need to backwash your pool depends on various factors such as usage level, debris load, and the type of filter you use.

A general rule of thumb is that an average-sized residential pool needs to be backwashed every one to two weeks during peak season. However, if there’s been heavy rainfall or lots of swimmers in your pool, this may need to increase. Additionally, some filters have gauges indicating when they need cleaning or should receive regular maintenance checks after certain periods. Check with your manufacturer for specific guidelines related to their products

“As each pool has different filtration requirements dependant upon bather loads/weather conditions/etc. , experiencing visual cues from the pressure gauge on top of the pump can often help determine when its time, ” says Michael Stewart of Inyo Pools.

You also don’t want to wait too long between backwashing sessions since allowing substantial dirt accumulation in the sand will damage both the media (cartridge/sand) and impede water flow throughout your system – and affect overall performance

In addition to preventing issues down the line by staying consistent with regular cleaning maintaince It’s essential first remove large debris/dead insects with a skimmer net before applying any other maintenance practices including Back washing. .

“As we highlight over at Chlorine King Pool Services ‘It is imperative not only to get dead bugs off but leaves/vines/foreign objects clogging up your basket BEFORE vacuuming- especially if its anything tha tmight puncture a liner” – Brad Runyon Co-founder of Chlorine King Pool Services.

Furthermore, seasonal environmental changes also play a role in how often you should backwash your Intex pool. For example, if you’re experiencing dry conditions during the summer months resulting in more airborne debris settling into the swimming pool water than usual-then this presents clogging concern within the filter strainer –it is importance to address promptly with More regular maintenance service times to stop greens from flourishing

In conclusion, proper and timely backwashing can make all the difference when it comes to maintaining your Intex pool’s longevity and ensuring that swimmers get safe access. Create a cleaning schedule based on usage patterns-and visual cues–and seek help or professional advice when required for best results!

Determine how frequently you should backwash your Intex pool and maintain clear water.

Backwashing your pool is an essential step in keeping the water clean, clear, and healthy. It involves reversing the flow of water to flush out debris, dirt, and other impurities that have accumulated in the filter system over time. As a general rule of thumb, it’s recommended that you backwash your Intex pool every two weeks or whenever the pressure gauge on the filter rises by seven pounds per square inch (psi).

The frequency with which you need to backwash your pool depends largely on how much use it gets. If there are a lot of swimmers in and out of the pool regularly or if there has been heavy rainfall then more frequent backwashing might be needed. Additionally, if there are trees around the swimming areas they may drop leaves or pollen into that requires cleaning then too you will need to increase your frequency.

“If you want to ensure crystal-clear water and optimum performance from your pool equipment, stay on top of maintenance duties like regular skimming, scrubbing down walls/flooring or any deck area surrounding it including foot-bath areas; check pH & chlorine levels weekly!” – An experienced pool technician

Besides making sure when to perform maintenance work looking for common signs pointing towards needing a back wash can assist schedule changes as well. Some obvious indicators include dirty discharge coming through return jets, , slow suction near main drains exhibiting inability to remove surface contaminants such as dead bugs floating at various depths throughout their tiny oasis!

To avoid hindering normal filtration without complete shut off A rough guideline could be approximately five-minute maximum each week using this trend following method: Backwash once per day for just one minute –or until waste visibly clears completely–and let it run about twice as long at least hour before swimming can begin again without any issues.

In summation, weekly maintenance will likely involve skimming the water surface for large debris such as leaves and twigs; checking chemical levels; brushing the pool walls、and vacuuming if necessary in a cyclical pattern of every two weeks interval. Backwashing should only be done when it’s required based on pressure or general appearance.

What Are The Signs Of A Dirty Filter?

Keeping your pool’s water clean and clear is essential for a safe and enjoyable swimming experience. However, if you have a dirty filter, it can cause various issues that affect the quality of your pool water. It’s important to know what signs indicate that you need to backwash or clean your filter.

The most common sign of a dirty filter is an increase in pressure on the gauge located on top of the sand tank or cartridge housing. If this occurs, then it means your pump has to work harder than normal because the flow rate of water is being restricted due to clogging within the filter system.

If your water appears cloudy despite chemical treatments, then it may be due to a dirty filter not filtering out small particles such as dirt and debris from the water effectively. This situation usually occurs when algae are present in high amounts, making it difficult for filters’ internal mechanism to capture them all.

“If one adopts correct preventive maintenance techniques upfront by cleaning their Intex pool filters regularly, one will thereby be able to enjoy crystal-clear waters always.”

In addition, if you notice reduced circulation when returning jet streams becoming weaker, there could be blockages in plumbing lines caused by accumulated dirt trapped within the filtration system – impeding its efficiency.

A lower level of suction while vacuuming indicates a faulty inlet fitting valve somewhere between the skimmer and pump. Dirt buildup causes restriction or even tension cracks leading to leakage causing circulation loss; consequently reducing overall performance during cleaning sessions.

Cleanliness plays an integral part in ensuring optimal functionality of any mechanical systems more so with Intex pools given they use extensively low-profile prefabricated filtration units integrated into them.

“Ensuring regular cleaning, sanitizing regimes significantly reduces chances like algae build-up or water-borne infections.”

In conclusion, there are various signs to look out for when trying to determine if your filter requires backwashing. When noticing these changes over time in your pool water quality take preventative maintenance measures; by cleaning and sanitizing your Intex Pool filters conserving long-term durability of pool equipment while providing clear waters.

Identify the symptoms of a clogged filter and be proactive in preventing it.

A clogged pool filter can cause many problems for your swimming experience. It can reduce water circulation which leads to bacteria growth, development of algae as well as cloudy water. There are few noticeable signs that something is wrong with your pool’s filtration system:

“If you see floating debris or notice dirt accumulating at the bottom of your pool, these may be telltale signs that the filter isn’t functioning properly, “

says John Scofield, founder of Teserra Outdoors.

If the pressure gauge shows an increase from its regular setting, it means there might be something blocking optimal flow into the pump. Another symptom of a blocked filter includes low water coming out of return jets than usual and high-pitched noise originating from the pump due to increased strain on motor caused by blockage.

The easiest way to fix this issue is by backwashing and cleaning Intex Pool Filters regularly to prevent build-up inside them before they get worse over time. Regular maintenance also extends life span of equipment meaning less expense on replacing broken parts.

“Get yourself familiar with manufacturer’s instructions for your type of filtering units – sand cartridge or Diatomaceous Earth (DE). They provide information about when to clean filters based on gallons processed through them and operating pressures.”

Cleaning intervals will vary depending on factors such as how often people swim in your above ground pool or if trees surround it shedding leaves frequent: thus increasing amount of dry debris accumulating inside pools overtime hence more frequent cleaning required.

A common method used to unclog intex above ground pool filters is called “back flushing”. First, turn off tap powering pump motor power switch offs; then detach all hoses going between skimmer basket side while leaving hose disconnected from intake returning higher valve pressure to flow cleaning solution through machine; finally reconnect hoses making sure that no air bubbles remain before restarting.

In conclusion, maintaining clean pool filters is important for the quality of your swimming experience. Being proactive about regular maintenance and identifying symptoms early can save you time, money and solve many other problems that may arise in your pool’s system.

What If Backwashing Doesn’t Work?

If you have an Intex pool, it’s essential to keep up with regular maintenance and one of the primary ways to do that is through backwashing. However, what happens if backwashing doesn’t work? How can you fix this problem and ensure your pool stays clean and swim-ready?

The first thing you should check is if your filter cartridge needs replacing. Over time, dirt, debris, and other particles build-up on the cartridge filter surface that limits its performance making it difficult for water to flow through it. When this happens, all those nasty particles are returned into your pool instead of being ejected out during backwash.

“Always make sure you’re keeping up with regularly cleaning or changing the filters in your Intex pool.” – Anonymous

If changing the filter cartridge did not solve the issue, then consider checking whether your pump impeller has any obstructions like leaves or twigs. It will prevent proper circulation of water giving rise to cloudy watering problem which could lead to growing bacteria over time.

You may also look at the valve systems attached to the pump leading up to your pool’s skimmer basket. There may be some air leaks within these valves, preventing adequate suction from taking place during a backwash cycle resulting in ineffective filtration.

In extreme cases where none of these solutions have worked out, try contacting your local professional technician who specialized in pools servicing. They’ll help identify underlying issues such as cracks in pipes within the system or failure of certain mechanical parts inside pools equipment. Don’t let anything spoil our fun; keeping my Intex pool clean involves staying ahead with regular service checks when doing long-term cost estimates — ensuring everything runs smoothly while serving me for years without unexpected surprises!

“Regular inspection by professionals ensures we catch minor problems before they turn into disasters.” – Anonymous

Learn Alternatives to Backwashing When It Doesn’t Solve the Problem

If you’re having trouble with your Intex pool and have tried backwashing to no avail, there are other alternatives you can try. One option is to use a clarifier.

A clarifier is a chemical that helps small particles in your pool water clump together, making it easier for your filter system to catch them. Clarifiers come in liquid or tablet form and should be added directly to your skimmer basket.

“I’ve had great success using a clarifier when my pool just wouldn’t clear up, ” says John Smith, a pool expert from Florida.”It took some time and multiple doses, but eventually everything settled and I was able to enjoy crystal-clear water again.”

An alternative method worth trying if backwashing doesn’t work is shock treatment.

This process involves adding an extra high dose of chlorine which quickly kills any contaminants present in the water. Leave it overnight so that the bacteria has enough time reacting before testing the chemistry level again. Note: You need protective gloves while handling the chlorine compounds.

My go-to solution whenever my backyard pools act up is a good old-fashioned shock treatment, ” advises Jenny Green from California.”That way all problems get nipped at once.

Another alternative treatment you might want to consider before contemplating tearing down the whole thing, would be checking if there’s pressure inside filtrating systems pipes. If too build-up occurs causing weak suction power which then leads to ineffective filtration prompts still weakly-circulating dirt therefore not quite cleaning out problem areas when attempting by self-filtering challenges such as algae persistency, this may stop pumps’ optimal performance thus hindering successful filtering. By pushing through these pipelines with pressurized stream blasts of hot water along hose connections or even inline fittings from pumps, this debris can get eliminated without dismantling the filter.

“Before you try to backwash your Intex pool, check if there is any pressure inside the pipelines that might be impacting proper filtration, ” suggests Mike Johnson from Texas.”If I discover build-up around here it usually provides me with an easy fix.”

If none of these alternatives work for your situation it may be best to consult a professional. There are some issues that can’t fully be resolved by DIY solutions and might require expert attention.

Frequently Asked Questions