How To Drain Water Around A Pool? [Facts!]

Spread the love

For many people, swimming pools are a frequent source of relaxation and fun in the summer. Unfortunately, there are some things that you need to be careful of when it comes to maintaining the pool. One of these things is the water level; if you forget to drain the water around your pool on a regular basis, then it will eventually overflow and cause some problems. If you want to really enjoy your pool, then you need to learn how to drain it properly so that you do not have to worry about the water level when you are not around. In this article, we’ll discuss how you can drain water around your pool on a regular basis so that you can enjoy it without any worries or troubles.

Get The Right Tools

In order to drain water around your pool you first need to get the right tools. Fortunately, this should not be that difficult; you can get a simple hand pump that can be operated manually by standing next to it and pumping for a few minutes several times a day. If you do not have a hand pump, then you can either get an electric or hydraulic submersible pump. If you live in a warmer climate, then an electric submersible pump might be a good choice for you as they are generally easy to use and maintain. Regardless, you should try to get a manual hand pump first to have the flexibility of controlling the flow of water when pumping. You should also consider upgrading your equipment so that you can have a more steady stream of water during the times when you are using it.

Set Up The Drainage System

Once you have obtained the necessary tools, you need to set up the drainage system around your pool. For this, you will need to dig a small ditch around the perimeter of your pool. This is typically a 3-5 foot trench that is covered by a grate that you can remove for cleaning purposes. You should also consider lining the trench with a waterproof material such as concrete or plastic to prevent any damage from occurring from exposure to the elements. Once you have finished digging the trench, you need to set the drainage basin at the bottom and ensure that there is enough room for the water to flow when it is pumped. You can either set up an overflow pool to collect the water or just let it flow directly to the street or gutter outside of your home.

Install The Cylinder

Once you have installed the drainage system, you need to connect the intake tube on the side of your pool to the cylinder. Make sure that the connection is sealed and that there are no holes present in the area that is near the connection point. To ensure that the water flows smoothly, you should remove any debris and excess soil from around the intake area so that there are no blockages present. Once you have removed any debris around the intake area, you should clean and dry it before connecting the tube to the cylinder.

Connect The Shut-Off

Once you have installed the cylinder, you need to connect the shut-off valve on the end of the tube that is located near the bottom of your pool. Make sure that this valve is properly sealed and does not have any leaks or openings present. You should also check for any damages or wear on the area that is near the connection point of the tube. If you find any damages or wear, then you should either fix them or replace the component so that the water flows smoothly.

Adjust The Degrees

After you have installed all of the necessary components, you need to go back to the beginning and find the appropriate drain plug that best suits your needs. You should consider using a plug that is made for outdoor use as they are typically more durable than those made for indoor use and are designed to last longer under adverse conditions. Once you have found the correct plug, you should tighten it all the way up and ensure that there are no leaks present. You should also check for any adjustments that need to be made near the connection point of the tube as this is where most of the problems arise. If there are any adjustments that need to be made, then you should either tighten or loosen the plug depending on what needs to be done.

Test The System

Once you have finished installing all of the necessary components, you need to test the entire system to make sure that it is working correctly. Start by turning on the valve at the end of the tube so that the water starts draining from your pool. If you have an electric pump, then you should check for any electrical leaks or shorts before testing the system. If the water is not draining correctly, then you should either check for any blockages or debris that may be preventing the flow of water or replace some of the components so that the system can be tested again.

To summarize, in order to drain water around a pool, you need to get the right tools, set up the drainage system, install the cylinder, connect the shut-off, and adjust the degrees. Once you have tested the system and it is working correctly, you can enjoy your pool without any worries or troubles.

Do NOT follow this link or you will be banned from the site!