How To Drain Water From Pool After Rain Australia? [Fact Checked!]

Spread the love

Sometimes, we are not even aware of how much water we actually need to avoid dehydration. It is always good to be informed of the current status of your pool. Especially if you live in Australia where it can be really hot and humid, you want to make sure that your pool stays clean. There are frequent heavy downpours of rain that can cause all sorts of problems if they’re not properly absorbed by the ground. Therefore, it is crucial that you understand how to drain water from pool after rain Australia.

Why Should You Drain Your Pool After A Heavy Rainfall?

If you have a pool and you live in Australia where it rains a lot, there are a few reasons why you should drain your pool after a heavy downpour:

  • To stop the growth of algae and moss on the pool walls
  • So that the water doesn’t accumulate and cause the carpet or the floor to become waterlogged
  • To prevent the pipes from getting clogged up by the excess amount of water
  • To prevent the pool furniture from being damaged by water surging against it
  • To lessen the chances of injuries from accidents with water
  • To allow for more accurate pH testing of the water
  • To give the water time to settle before reusing it
  • To allow for disinfection with more effectiveness
  • To prevent the pool filter from becoming jammed with debris
  • To reduce the amount of work needed for routine cleanings
  • To avoid the strain on the utilities caused by repeated interruptions for tank draining

How To Drain Water From Pool After Rain Australia?

Drain It At The Source

While it is always a good idea to drain your pool at the end of each day, don’t just leave it there. This will cause additional work for you in the long run. Instead, you should drain it at the source. This means that, after a heavy downpour, you will locate and shut off the supply valve(s) that lead to your pool. Once you have done that, the next step is to remove any debris that may be obstructing the inlet valve(s).

This will help mitigate the risk of water damage. Just remember that if you have a well-designed and well-constructed pool, this step is not necessary. The water will drain itself from the pool without any problems. However, if you are using an outside hose for bathing or for drinking, you will need to stop the flow of water from this source as soon as possible. This will minimize the risk of water damage.

Seal The Pool Area

Once you have drained your pool, it is a good idea to seal it off completely to keep the water contained. To do this, you will need to cover the entire inner surface of the pool with plastic. You can use either vinyl or aluminium foil as a pool cover. However, if you are planning to reuse the pool water, you will need to remove this cover. In this case, it is advisable to use either vinyl or aluminium foil.

Replace The Felt Pad On The Pool Table

On the opposite end of the pool, you will need to remove the felt pad that is protecting the table from becoming waterlogged. This is an easy step and you will be able to do this with just a few screws. Once the felt is off, you can either spray down the surface with a hose or let it dry naturally.

Test The Water For pH

An important step to consider after draining your pool is to test the water for pH. Just go over to your local retailer and buy a basic kit that contains pH paper, a bucket, and some liquid. It is advisable to test the pH of the water after the pool has been drained and before you start using it again. If you add more than one pH paper to the water, it will be easier to monitor the changes in color and the degree of acidity or alkalinity.

The paper should turn yellow in an acid pool and blue in an alkaline pool. Remember that alkaline water can damage wood and marble, so you should always keep an eye out for these items when cleaning the pool. Also, make sure that the water is at room temperature before testing. If you heat the water, the results will be inaccurate.

Check The Pipes For Leaks

The last step before you can start using the pool again is to check the pipes for leaks. In some cases, it is easy to find these leaks and fix them temporarily using some grommets or silicone caulk. If you find that the leaks are more widespread or if they are causing serious damage, you will need to either replace the whole pipe or have a qualified plumber locate and repair them. This step is important because it prevents water damage and discomfort in the long run.

As you can see, there are multiple benefits to draining your pool after a heavy rain. Make sure to follow these simple steps to ensure that your pool stays clean and that you don’t have any problems in the future. If you regularly get heavy rainfalls, you will need to consider upgrading your pool equipment or having it custom made. The last thing anyone wants is a leaking pool. Especially since it is so difficult to find the source of the leak when it is already inside your home.

Do NOT follow this link or you will be banned from the site!