Resetting an automatic pool chlorinator is pretty easy. Just follow these steps:
Table of Contents
Check The Manual
The first step is to make sure you read the manual that came with the chlorinator. This will tell you all the tricks and tips for using it. When you are done, you can simply reset it and start using it as soon as possible.
Empty The Tank
The next step is to empty the tank that holds the salt water. You will need to remove the pump that circulates the water in the pool. Once you have emptied the tank, take some time to let the water settle down. Then you can rinse the tank and refill it with fresh water.
Clean The Tank And The Pump
When you are done with the tank, you will need to clean all the inside surfaces with soap and water to keep things clean. Then you can dry the tank and the pump thoroughly before refilling them.
Check The O-Ring
The last step before you use the chlorinator again is to check the O-ring that surrounds the pump. This is where the grease and oil that is built up from the continuous use of the pump will clog the ring. You can either remove this ring and put it back when you are done using the pump or just replace it when needed.
Reset The Timer
When you have followed the steps above and reset the timer, the saltwater pool chlorinator will start working smoothly again. You can leave it set on automatic mode or you can set it for a certain period of time and then turn it off. When the timer is turned off, the pump will stop working and the pool will become undrinkable for about 15 minutes. During this time, you have to either drain the pool or use a bucket to remove the water for you to be able to drink it or use it for other purposes.
If you use the automatic setting, the timer will start working as soon as you turn on the pump. This means the pool will not become undrinkable for long. However, if you set the timer for a longer period of time, the pool will become undrinkable for about 15 minutes after each use. This is why it is important to clean the tank and the pump after each time you use them.
If the timer gets stuck at 0 for some reason, you can remove it and set it to auto again. Make sure you flush the unit once you have reset it to ensure the correct connection and no damage to the wiring. If this happens, you will need to replace the entire unit.
If you use the automatic mode and the pump gets stuck at 0 after a while, this usually means there is a hair plug in the pump or a piece of debris has become lodged in the pump. You can use a brush or your fingernails to remove any debris that might be causing the problem. If the problem persists, you will need to take it to a technician for repair or replace the pump.
How To Prevent Salt Water Pool Clorification
It is important to prevent saltwater pool clorification as much as possible so that your pool stays clean all year long. Always ensure the proper chlorine level is maintained in your pool by using a salt water pool chlorinator. This will help keep the water crystal clear and give you and your family all the benefits of swimming in fresh water anytime you want. If you are looking for ways to prevent this, here are some of the best tips:
Check The Water Quality
One of the best ways to keep your pool free from all the gunk that you just cannot scrub away is to be sure the water quality is always tested on a regular basis. This will let you know if there are any problems before they get too bad. You can do this either by purchasing a home water quality tester or by asking your local water company to test the water for you. The choice is up to you.
Use Cleaning Products
It is important to know how to clean your pool equipment properly. You will always need to clean the pool and the pool equipment after every use so as to keep the water clean. If you use many chemicals to clean the pool, you will eventually run out of cleaning products. To avoid this, simply make sure you replace the chemicals every month or every other month. This will help extend the life of your pool chemicals and give you all the benefits of keeping your pool clean all year long without any worries of running out of chemicals.
Dont Overuse The Chemicals
The last thing you want to do is to overuse the chemicals that you are using to keep your pool clean. This will result in poor water quality and dangerous algae blooms. In some cases, the algae can even grow in large amounts and cause serious health problems for you and your family. To avoid this, make sure you use the chemicals only when needed and then clean the pool immediately after use. If you leave any residue behind, you will have to remove it with a scrub brush or sponge filter.
Practice Good Swimming Hygiene
It is also very important to practice good swimming hygiene. This means always washing your hands before and after using the pool. Also make sure to clean the pool toys and gear regularly to keep things like germs and bacteria at bay. Simply put, keep your pool clean and worry-free by following the steps above and using a saltwater pool chlorinator continuously throughout the year. Your family will thank you for this and so will your friends who are also lucky enough to enjoy the benefits of a clean pool.