How To Siphon Water From Inground Pool? [Solved!]

Spread the love

Anyone who owns an above-ground pool might already be experiencing the aggravation of having to go through a glass wall in order to fill it up with fresh water. There will be times that you’ll want to take a dip in your pool, but if it’s above ground, there’s always the chance of it flooding, especially if it’s a heavy downpour that we’re experiencing at present. Naturally, this is something that you don’t want to happen. So what can you do about it? You might consider installing an underground pool, which can be filled with fresh water via a vacuum system that draws directly from the hydrant. While this might sound like an expensive option, the expense is definitely worth it if you end up saving tons of time and effort on your part in maintaining a clean, safe and functioning pool. So here are some helpful tips on how to siphon water from an inground pool:

Get Everything You Need

When designing an underground pool, where you will be placing the intake and ejection points is vital. While you don’t want to put the intake anywhere near the surface, you also don’t want it to be too far down either. This is mostly due to the height of the water table in your area. If you want to avoid having your pool drained in the event of heavy rain or flooding, putting the intake elsewhere would be the best option.

As for the ejection point, you want to make sure that it is in the right place. You don’t want to have any problems with the water backfilling your pool during a heavy downpour. So in the event that any of the above-ground pool’s plumbing has malfunctioned, your best bet would be to relocate the ejection point as well. Remember, the water level in your pool is always going to be higher than the water table outside. This means that even in the event of a small leak, there is always the possibility of your pool being flooded. With this in mind, you must take the time to locate the weak points in your pool’s plumbing and repair them before you start working on replacing any of it.

Clear The Area

After you’ve gotten everything you need, it’s time to clear the area around your pool. You want to make sure that there is nothing in the way when you’re siphoning the water. This means getting rid of any trees or shrubbery that might be in the way. If you have a sandy or gravel lot, you might also want to do some landscaping around the pool area. This is going to help with the water’s natural drainage, so there will be less of a chance of it ponding anywhere. In addition, you might want to dig some holes in order to place some sprinkler heads around the area. This helps with even distribution of the water and prevents any standing puddles which could lead to mosquitoes breeding in them. It is important to note here that you are not required to do any of these things, but they can help improve the overall look and feel of your pool area.

Test The Plumbing

Once you’ve cleared the area and set up your pool, it’s time to test the plumbing. For this, you will need to shut off the water supply to your pool and then either run a hose from the faucet or open up the valves on the pool’s plumbing. While you don’t want to leave any of the valves open when you do this, it’s good practice to shut them all off before starting any work. Doing this ensures that none of the water is wasted when you start siphoning it. In addition, if you are drawing the water from an above-ground source, you will need to put in an additional supply pipe beyond what is already there in order to get the pressure you need to pull the water through. If there is no additional supply pipe, then you will need to either get a higher-pressure pump or find a way to boost the existing pressure from your city’s water supply.

Prepare The Area

After you’ve tested your pool’s plumbing, it’s time to start preparing the area around it. This is where you will place the intake valve for the vacuum pump as well as the area where the water will be stored once it has been sucked in. In addition to this, you will want to put down some gravel or crushed coral on which to sit when taking a dip. This will help with the overall feel and look of the area, as well as reducing water deterioration due to exposure to sunlight.

Assemble The Equipment

Now that you have your area prepared, it’s time to start assembling the equipment. For this, you will need to connect the vacuum line from the pump to one of the pool’s plumbing valves (depending on which one you used for testing), then run the other end of the line to an ejection (drain) valve. Once this is done, you can turn the water back on and start seeing results. You might need to do this a few times before everything settles in and the water starts flowing consistently.

If this seems like a daunting task, don’t worry; it’s something that you can accomplish with a little bit of effort. Just make sure that when you’re done, you put everything back where it was before you started. This includes picking up all the bits and pieces that you’ve put down, as well as re-clearing the area around your pool. Be sure to wear protective clothing and gloves during this process, as there is always the chance of getting wet during the siphoning operation.

Do NOT follow this link or you will be banned from the site!