Did you know that it’s very easy to turn your pool water into fresh drinking water? All it takes is a little bit of elbow grease and a few tools. You will not need a chemistry background to pull this off. All the information you need is available online. Here are the steps to follow:
Table of Contents
Step 1: Get The Equipment
The first thing you need to do is to get all the equipment. You will need a strainer to filter the pool water. You also need equipment to clean the water. You can’t just use any old rubbish to clean your pool. You need a pool vacuum to suck up all the gunk at the bottom of the pool. Additionally, you need a skimmer to take out the scraps at the surface. You don’t need all of this equipment to turn your pool water into drinking water, but it’s nice to have everything in one place so you don’t have to search for things when you need them. Once you have all of this equipment, it’s time to move on to the next step.
Step 2: Add Chemicals
Adding chemicals is the next step, and this is where things get a little bit more complicated. You need to add an oxidizer to enable the coagulation process, and you need a reducer to help break down the solids in the water. The trouble with adding chemicals is that if you don’t add the right amount, the process won’t work, and if you add too much, the water will become unusable. To avoid this, you need to refer to the instructions that come with the chemistry that you are using. If in doubt, ask your pool professional for help. It isn’t complicated, but you must follow the instructions carefully. If you want to turn your pool water into drinkable water, this is the process you need to follow:
Step 3: Test The Water
When you are using chemicals, it is important to test the water to see if the chemicals have worked. You need a liquid testing kit to test for PH, oxidation reduction potential, and calcium hardness. You need to test for these things before and after you add the chemicals so you can determine whether or not they worked as intended. You can save the results of these tests for later when you report back to your pool professional. This is also a good place to check for chlorine and cyanide contamination. Once you are familiar with these tests, it’s easy to determine whether or not the chemicals you are using are worth continuing with, or if you should try another brand or type. Most importantly, testing the water is an easy way to ensure that you are following the correct process. If you add the chemicals and it doesn’t work, then you go back and try something else. This is much easier than trying to troubleshoot a process that isn’t working as planned. Never, ever, try this procedure without testing the water first.
Step 4: Filter The Water
Adding chemicals will often cause the water to turn thick and gummy, but that is exactly what you want. Now that you have a gummy mass at the bottom of the pool, you need to strain it through a filter. It is very important to use a proper filter for this step. You must use a media filter with a sand layer at the bottom. You can use gravel, crushed coral, or small shells to line the bottom of the filter. Do not use large shells as these will clog the filter quickly. Your liquid testing kit will tell you which type of filter you need. Once you have your filter, it’s time to put it in place and seal it up. Make sure you get all the gunk at the bottom of the pool and filter it through your system. If any part of your pool water remains unstrained, then it will attract mosquitoes and other insects that could cause an unhealthy environment. To avoid this, make sure you strain the entire pool water each and every time you clean it.
Step 5: Distribute The Water
After you have strained the water through the filter, it is time to distribute the water around your pool. Remember, all water has plants and animals that live in it, and you don’t want to disturb these living things by distributing the water too rapidly. With a little bit of planning and forethought, you can easily satisfy the needs of your pool without upsetting the balance of nature. If you don’t want to use a pool pump, then you can use the water dispenser at the bottom of the pool to deliver the fresh water to the top. Remember to shut off the water dispenser when you aren’t using it so that it doesn’t waste energy. You can also use a hose on your dispenser so that you can reach all parts of the pool. To avoid stagnation and the growth of bacteria, make sure you mix up the water and let it flow through the entire pool, including the shallow end where children are likely to dive in and get injured by sharp objects or unsupervised splashing.
Once you have followed these five easy steps, you will be able to drink your pool water without worry. If you keep adding chemicals and filtering the water, you can even turn it into very good drinking water that you can even serve to people. Congratulations! You just turned the dirtiest, filthiest, stickiest part of your body into something that is actually useful. Now you can enjoy your pool without worrying about contaminants or the safety of your water supply. Thanks for reading! We hope this article has helped you in your quest to make your pool water fit for drinking. If you have any questions or comments, please feel free to leave us a note at [email protected].