What Causes A Pool To Suddenly Lose Water? [Fact Checked!]


Sharing is Caring


You walk into your home pool area, and the water is perfect. You decide it’s time for a dive, and before you know it, the pool water is gone. What happened?

A lot of homeowners find themselves asking this question after experiencing this scenario. To give them an answer, we need to take a quick detour into the world of plumbing and find out what could have caused this huge loss of water from your pool. This blog post will discuss the most common reasons why your pool could have lost a massive amount of water without you knowing about it.

The Least Suitable Location For Putting In A Pool

If you’re fortunate enough to have a pool in your backyard, then you know that it requires a lot of space. It is generally accepted that a pool takes up a lot of room, so if you live in a small space, then putting in a pool may not be possible. Having a pool means you will be bound to have a bit of an area dedicated to it, so consider where you put it. If possible, go for a smaller one since they are more suitable for micro-homes.

Improperly Saturated Soil

If you’re planning on putting in a pool, then you will have to prepare the ground for it. The first step is to remove all plants and weeds that may be in the area, as these will prevent the ground from absorbing the needed water. When ready, spread a two to three inches of gravel on the ground, and rake it smooth. Next, add another inch of gravel and smooth it again. When finished, water the area well and let it settle for a minute or two. After this, you can proceed with the installation of the pool.

Excessive Water Intake From Rain

Water intake from rain is a common problem, especially in areas with a lot of rainfall. It is necessary to have the gutters cleaned out at least once a year, and if possible, replaced. After the annual cleaning, check for any signs of moisture in the siding or roofing of your house. Moisture in these areas is an indicator that you’re taking in more water than you can handle. A good way to combat excessive water intake is to add a pool skimmer device to your pool. These are automatic pool cleaners that will suck up all the dirt and debris that would normally make its way to the bottom of the pool. The advantage of having a pool skimmer is that you don’t have to constantly check the water levels, and it does a good job of keeping the pool clean. A disadvantage of this automated device is that it will eventually clog up and need to be repaired or replaced.

Too Much Water Going Down The Drain

Did you know that your toilet can be a source of water loss? Unless you have a water-saving toilet, all the water you flush will eventually find its way to the pool. This is one of the many reasons why it is not a good idea to directly connect your toilet to the pool. Instead, install a water-saving toilet, and you will see considerable amounts of water savings. In some cases, a water-saving toilet can improve the efficiency of your pool by 30%.

Not Properly Ventilated

The second most common reason why your pool could be losing water is because there is no proper ventilation. This can happen if any of the following is true:

  • There are no proper openings in the area where the water meets the air
  • You have installed a pool cover, but this cover is made of a material that prevents air circulation
  • There is no proper opening in the roof where the warm air can escape
  • The windows do not allow the necessary flow of air
  • There is no proper opening in the wall where the water flows to the outside

To solve this problem, you will need to either install fans to move the air or open up the areas where the air meets the water. Remember that air can always flow towards a source of lower pressure, so be sure to always have the pressure readjusted whenever there is a change in the weather conditions.

Improperly Perforated Piping

Piping is a commonly referred to as the โ€œtubingโ€ that runs throughout your pool area. It is important to have this piping properly perforated, so dirt and debris cannot build up around them. When the time comes to clean your pool area, it will be much easier to remove all the gunk that has accumulated around these crucial parts of your home. To ensure this, take the time to run a proper garden hose around the outside of your pool, and be sure to clean all the areas near the pool pump and filter. Be careful not to let any of the water spill out into the area where it can cause damage or be difficult to remove once it has settled.

Dry Spring

A dry spring means there is no proper flow of water from the ground. This could be due to a number of reasons, including:

  • The sprinkler system is malfunctioning
  • The soil is dry
  • There is no natural ground water flow in the area
  • The property is located in a semi-arid climate, and as a result, there is very little rainfall (less than 10 inches per year)
  • The property needs a lot of water to sustain life

To make your pool function properly, you will need to either correct the issue causing the dry spring, or add more water to it. This is why it is essential to closely monitor the levels of water in your pool. It is also advisable to have the water tested at least once every month, just to be sure there are no issues causing the pool to lose water. If you suspect there is an issue, then call a professional immediately for help. They will be able to tell you what is wrong and how to fix it. In some cases, additional materials may be needed to correct the problem (such as sand or pebbles), so be sure to have these items on hand when the plumber arrives.

In summary, there are several different reasons why your pool could be losing water. By understanding the issue, you will be in a better position to address it and prevent further water loss. If you think that your pool is acting strangely, then call a professional immediately for help. They will be able to determine what is causing the problem and how to fix it.

Craving More Content?

Pool Tips USA